Truma spare parts

Accessories

Adapter kit AL-KO M short to 1800 kg

For AL-KO frames with offset axle and a permitted total weight of up to 1800 kg.

Adapter kit AL-KO M short to 1800 kg

For AL-KO frames with offset axle and a permitted total weight of up to 1800 kg. For frame edge compensation when the frame is pushed together as far as possible.

Also suitable for

  • Mover SR
  • Mover SE
  • Mover SE R

Mover PowerSet

Together with the suitable battery, provides the power for the Mover. Consists of the charger BC 10, terminal clamps, temperature sensor and battery cut-off switch. 

Mover PowerSet with charger BC 10

Together with the suitable battery, provides the power for the Mover. Consists of the charger BC 10, terminal clamps, temperature sensor and battery cut-off switch.

  • Charger can be removed in one action thanks to the plug-and-play connection
  • Charges all 12 V lead acid batteries
  • Optimised charging curve for each battery type
  • Current charge status can be seen on LED display 

Battery cut-off switch

Interrupts the circuit and prevents the risk of short circuits. Is connected to the positive pole of the battery. Also useful as an additional anti-theft device.  

Battery cut-off switch for more safety

Interrupts the circuit and prevents the risk of short circuits. Is connected to the positive pole of the battery. Also useful as an additional anti-theft device.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4 

Easy clicK terminal clamps

Connect and disconnect battery connections quickly and easily by hand. Suitable for all DIN and SAE connections. Suitable for currents up to 150 A at continuous load, 800 A at short-term load. 

Easy clicK terminal clamps for the battery

 Connect and disconnect battery connections quickly and easily by hand. Suitable for all DIN and SAE connections. Suitable for currents up to 150 A at continuous load, 800 A at short-term load.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4

Eriba Troll adapter kit

Allows the installation of the Mover behind the axle of an Eriba Troll caravan.

Mover Eriba Troll adapter kit

Allows the installation of the Mover behind the axle of an Eriba Troll caravan.

Suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover XT

 

Adapter kit for AL-KO M frame 1900 – 2000 kg

To balance out frame edges for the single-axle chassis AL-KO chassis M with continuous frame and a maximum permitted weight of 1900 kg to 2000 kg. 

Adapter kit for AL-KO M frame 1900 – 2000 kg

To balance out frame edges for the single-axle chassis AL-KO chassis M with continuous frame and a maximum permitted weight of 1900 kg to 2000 kg. 

Also suitable for:

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R

 

Adapter kit for AL-KO M frame to 1800 kg

To balance out frame edges for caravans with AL-KO M chassis with axial movement to 1800 kg maximum permitted weight.

Adapter kit for AL-KO M frame to 1800 kg

To balance out frame edges for caravans with AL-KO M chassis with axial movement to 1800 kg maximum permitted weight.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R

Installation kit for AL-KO Vario III / AV

Metal plates reinforce the frame and must be used for installation of the Mover on caravans with AL-KO Vario III / AV Single Chassis with a frame thickness of less than 2.8 mm. 

Installation kit AL-KO Vario III / AV for frame reinforcement

Metal plates reinforce the frame and must be used for installation of the Mover on caravans with AL-KO Vario III / AV Single Chassis with a frame thickness of less than 2.8 mm.

Also suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover EM 

 

Low chassis kit, short

To balance out the height of caravans with a frame height less than 80 mm (all Mover XTs) or less than 110 mm (Mover SX) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Low chassis kit, short for height adjustment

To balance out the height of caravans with a frame height less than 80 mm (all Mover XTs) or less than 110 mm (Mover SX) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4

 

Low chassis kit

To balance out the height of caravans with a frame height less than 80 mm (all Mover XT) or less than 110 mm ( Mover SX) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV). 

Low chassis kit for height adjustment

To balance out the height of caravans with a frame height less than 80 mm (all Mover XT) or less than 110 mm ( Mover SX) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4 

 

Mover spacer kit 60 mm

To balance out the height of caravans with a frame height of < 140 to 80 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 60 mm for height adjustment

To balance out the height of caravans with a frame height of < 140 to 80 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 30 mm

To balance out the height of caravans with a frame height of < 170 to 110 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 30 mm for height adjustment

To balance out the height of caravans with a frame height of < 170 to 110 mm. Suitable for Mover systems built after 05/12. 

Short mounting system

Alternative mounting if the Mover cannot be attached because of substructures or interfering edges. In Germany, a test certificate (TÜV) is required, apart from Mover XT and Mover SX.

Short mounting system

Alternative mounting if the Mover cannot be attached because of substructures or interfering edges. In Germany, a test certificate (TÜV) is required, apart from Mover XT and Mover SX. 

Also suitable for

  • Mover SE R
  • Mover TE R
  • Mover TE R4 (2 pieces)

 

Eriba Touring adapter kit

Enables installation of a Mover on a chassis with a rectangular profile, such as the single-axle Eriba Touring caravan.
 

Mover Eriba Touring adapter kit

Enables installation of a Mover on a chassis with a rectangular profile, such as the single-axle Eriba Touring caravan.

Suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover XT 

 

Mover mudflap kit

Is used when the original mudflaps no longer fit after installation of the Mover behind the axle. Including instructions and template to adapt mudflaps. 

Mudflap kit for Mover manoeuvring systems

Is used when the original mudflaps no longer fit after installation of the Mover behind the axle. Including instructions and template to adapt mudflaps. 

  • Message
  • Service Helpline
  • Service Centre
  • Dealer search

One number for all cases:

+49 (0) 89 4617-2020

Do you have a question about a product, would you like to arrange an appointment with a Truma Service technician or do you need assistance? Just call us.

Service times:
Monday to Friday from 8 a.m. to 6 p.m.

If you have a question about an appliance, always have information about the appliance type, year of manufacture and factory number at hand. You'll find this on the type plate on the appliance.

Truma type plate

Visit the Truma service workshop!

Service directly from the manufacturer: The Truma Service workshop is located in Putzbrunn, near Munich, Germany. Our staff are very familiar with all Truma products, install devices and repair devices that have already been installed.

Service times

May to September
Monday – Thursday: 7:30 a.m. – 4:30 p.m.
Friday: 7:30 a.m. – 3 p.m.

October to April
Monday – Thursday: 7:30 a.m. – 4:30 p.m.
Friday: 7:30 a.m. – 4 p.m.

To arrange an appointment, call

+49 (0) 89 4617-2020


Truma Servicewerkstatt
Michael-Haslbeck-Straße 13
85640 Putzbrunn, Germany

No sale of spare parts / Please do not send any equipment to Truma without being requested to do so.

Find your nearest Truma Service Partner

We use cookies to ensure optimum design and continuous improvement of our website. By using the website, you agree to the use of cookies. Accept More information