Man couples caravan with a mover on a car

Mover smart M

Manoeuvring assistant with manual engagement and disengagement for single-axle caravans

Truma Mover XT
  • Manual engagement and disengagement with a lever movement from one side – no cranking required
  • Start off smoothly, stop with precision
  • Manoeuvre with ease using the handy remote control
  • Simple installation on all common frames
  • No TÜV-registration required thanks to general operating permit

M for manual: The Mover smart M

The Truma Mover smart M is the semi-automatic entry-level model among the Truma manoeuvring assistants. It impresses with its unbeatable price/performance ratio and highest Truma quality. The drive rollers are engaged on the tyres by hand with just one lever movement – and you're already good to go!

With the remote control, you can control your caravan intuitively at the push of a button. Thanks to the soft-start function, the caravan starts off without jerking, and only then is the speed increased. As soon as you release the control knobs, the caravan's brakes are applied. This guarantees maximum safety.


What the Mover smart M can do:

  • Copes with inclines of 13 percent
  • Simple, accurate coupling to the towing vehicle
  • Suitable for single-axle caravans up to 1800 kilograms

The non-slip surface of the drive rollers ensures the required grip on the tyre and enables optimal power transmission. The rollers are particularly low-wearing yet also light – made possible by the use of cast aluminium.

Replace comparison appliance Add for comparison Back

Compare Truma manoeuvring assistants for caravans

Truma Mover smart M

Semi-automatic manoeuvring assistant at entry-level price for single-axle caravans up to 1800 kilograms.

Permitted total weight 1800 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 28 A
1800 kg
Maximum power consumption 100 A
Quiescent current consumption < 20 mA
Speed (depending on weight and incline) approx. 15 cm per second
Swivelling in/out manual
Remote control for manoeuvring included
Radio frequency
Max. climbing capacity 13 % with 1800 kg
Weight ca. 33 kg

Truma Mover smart A

Fully automatic manoeuvring assistant at entry-level price for single-axle caravans up to 2000 kilograms.

Permitted total weight 2000 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 35 A
2000 kg
Maximum power consumption 125 A
Quiescent current consumption < 20 mA
Speed (depending on weight and incline) approx. 15 cm per second
Swivelling in/out automatic
Remote control for manoeuvring included
Radio frequency
Max. climbing capacity 13 % with 2000 kg
Weight ca. 32 kg

Mover XT

Electric swivelling manoeuvring system with two motors for single-axle caravans up to 2300 kilograms.

Permitted total weight 2300 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 25 A
2300 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug/adapter plugged in) < 0.15 mA (plug/adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2, 868 MHz
Max. climbing capacity 13% with 2300 kg
Weight approx. 28 kg

Mover XT L

Electric swivelling manoeuvring system with two motors for single-axle caravans up to 1500 kilograms.

Permitted total weight 1500 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 20 A
1500 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug/adapter plugged in) < 0,15 mA (plug/adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2, 868 MHz
Max. climbing capacity 20 % with 1500 kg, 25 % with 1200 kg
Weight approx. 28 kg

Mover SX

Manoeuvring assistant with manual engagement and disengagement for single-axle caravans up to 2000 kilograms.

Permitted total weight 2000 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 28 A
2000 kg
Maximum power consumption 120 A
Quiescent current consumption < 20 mA
Speed (depending on weight and incline) approx. 16 cm per second
Swivelling in/out manual
Remote control for manoeuvring included
Radio frequency Class 1, 868 MHz
Max. climbing capacity 13 % with 2000 kg
Weight approx. 35 kg

Mover XT2

Electric swivelling manoeuvring system with two motors for twin-axle caravans up to 2400 kilograms.

Permitted total weight 2400 kg
Trailer type Twin axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 25 A
2300 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug / adapter plugged in) < 0.15 mA (plug / adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2.868 MHz
Max. climbing capacity 10% with 2400 kg
Weight approx. 28 kg

Mover XT4

Electric swivelling manoeuvring system with four motors for twin-axle caravans up to 3100 kilograms.

Permitted total weight 3100 kg
Trailer type Twin axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 36 A
3100 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug / adapter plugged in) < 0,15 mA (plug/adapter not plugged in or after 1 hour withplug / adapter plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2.868 MHz
Max. climbing capacity 10% with 3100 kg
Weight approx. 60 kg

Mover SX

Manoeuvring assistant with manual engagement and disengagement for single-axle caravans up to 2000 kilograms.

Permitted total weight 2000 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 28 A
2000 kg
Maximum power consumption 120 A
Quiescent current consumption < 20 mA
Speed (depending on weight and incline) approx. 16 cm per second
Swivelling in/out manual
Remote control for manoeuvring included
Radio frequency Class 1, 868 MHz
Max. climbing capacity 13 % with 2000 kg
Weight approx. 35 kg

Truma Mover smart A

Fully automatic manoeuvring assistant at entry-level price for single-axle caravans up to 2000 kilograms.

Permitted total weight 2000 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 35 A
2000 kg
Maximum power consumption 125 A
Quiescent current consumption < 20 mA
Speed (depending on weight and incline) approx. 15 cm per second
Swivelling in/out automatic
Remote control for manoeuvring included
Radio frequency
Max. climbing capacity 13 % with 2000 kg
Weight ca. 32 kg

Mover XT

Electric swivelling manoeuvring system with two motors for single-axle caravans up to 2300 kilograms.

Permitted total weight 2300 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 25 A
2300 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug/adapter plugged in) < 0.15 mA (plug/adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2, 868 MHz
Max. climbing capacity 13% with 2300 kg
Weight approx. 28 kg

Mover XT L

Electric swivelling manoeuvring system with two motors for single-axle caravans up to 1500 kilograms.

Permitted total weight 1500 kg
Trailer type Single axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 20 A
1500 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug/adapter plugged in) < 0,15 mA (plug/adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2, 868 MHz
Max. climbing capacity 20 % with 1500 kg, 25 % with 1200 kg
Weight approx. 28 kg

Mover XT2

Electric swivelling manoeuvring system with two motors for twin-axle caravans up to 2400 kilograms.

Permitted total weight 2400 kg
Trailer type Twin axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 25 A
2300 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug / adapter plugged in) < 0.15 mA (plug / adapter not plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2.868 MHz
Max. climbing capacity 10% with 2400 kg
Weight approx. 28 kg

Mover XT4

Electric swivelling manoeuvring system with four motors for twin-axle caravans up to 3100 kilograms.

Permitted total weight 3100 kg
Trailer type Twin axle
Operating voltage 12 V DC
Average power consumption on even ground at a total weight of 36 A
3100 kg
Maximum power consumption 150 A
Quiescent current consumption < 80 mA (plug / adapter plugged in) < 0,15 mA (plug/adapter not plugged in or after 1 hour withplug / adapter plugged in)
Speed (depending on weight and incline) approx. 17 cm per second
Swivelling in/out electrical
Remote control for manoeuvring included
Radio frequency Class 2.868 MHz
Max. climbing capacity 10% with 3100 kg
Weight approx. 60 kg

Accessories for the Mover smart M

Find suitable accessories for your Truma Mover smart M.

Mover PowerSet

Together with the suitable battery, provides the power for the Mover. Consists of the charger BC 10, terminal clamps, temperature sensor and battery cut-off switch. 

Mover PowerSet with charger BC 10

Together with the suitable battery, provides the power for the Mover. Consists of the charger BC 10, terminal clamps, temperature sensor and battery cut-off switch.

  • Charger can be removed in one action thanks to the plug-and-play connection
  • Charges all 12 V lead acid batteries
  • Optimised charging curve for each battery type
  • Current charge status can be seen on LED display 

Battery cut-off switch

Interrupts the circuit and prevents the risk of short circuits. Is connected to the positive pole of the battery. Also useful as an additional anti-theft device.  

Battery cut-off switch for more safety

Interrupts the circuit and prevents the risk of short circuits. Is connected to the positive pole of the battery. Also useful as an additional anti-theft device.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4 

Easy clicK terminal clamps

Connect and disconnect battery connections quickly and easily by hand. Suitable for all DIN and SAE connections. Suitable for currents up to 150 A at continuous load, 800 A at short-term load. 

Easy clicK terminal clamps for the battery

 Connect and disconnect battery connections quickly and easily by hand. Suitable for all DIN and SAE connections. Suitable for currents up to 150 A at continuous load, 800 A at short-term load.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4

Eriba Troll adapter kit

Allows the installation of the Mover behind the axle of an Eriba Troll caravan.

Mover Eriba Troll adapter kit

Allows the installation of the Mover behind the axle of an Eriba Troll caravan.

Suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover XT

 

Adapter kit for AL-KO M frame 1900 – 2000 kg

To balance out frame edges for the single-axle chassis AL-KO chassis M with continuous frame and a maximum permitted weight of 1900 kg to 2000 kg. 

Adapter kit for AL-KO M frame 1900 – 2000 kg

To balance out frame edges for the single-axle chassis AL-KO chassis M with continuous frame and a maximum permitted weight of 1900 kg to 2000 kg. 

Also suitable for:

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R

 

Adapter kit for AL-KO M frame to 1800 kg

To balance out frame edges for caravans with AL-KO M chassis with axial movement to 1800 kg maximum permitted weight.

Adapter kit for AL-KO M frame to 1800 kg

To balance out frame edges for caravans with AL-KO M chassis with axial movement to 1800 kg maximum permitted weight.

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R

Installation kit for AL-KO Vario III / AV

Metal plates reinforce the frame and must be used for installation of the Mover on caravans with AL-KO Vario III / AV Single Chassis with a frame thickness of less than 2.8 mm. 

Installation kit AL-KO Vario III / AV for frame reinforcement

Metal plates reinforce the frame and must be used for installation of the Mover on caravans with AL-KO Vario III / AV Single Chassis with a frame thickness of less than 2.8 mm.

Also suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover EM 

 

Low chassis kit, short

To balance out the height of caravans with a frame height less than 80 mm (all Mover XTs) or less than 110 mm (Mover SX, Mover smart) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Low chassis kit, short for height adjustment

To balance out the height of caravans with a frame height less than 80 mm (all Mover XTs) or less than 110 mm (Mover SX, Mover smart) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4

 

Low chassis kit

To balance out the height of caravans with a frame height less than 80 mm (all Mover XT) or less than 110 mm ( Mover SX, Mover smart) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV). 

Low chassis kit for height adjustment

To balance out the height of caravans with a frame height less than 80 mm (all Mover XT) or less than 110 mm ( Mover SX, Mover smart) and/or to bridge struts. If holes have to be drilled for installation on the chassis, in Germany the vehicle must be inspected by an official entity (TÜV).

Also suitable for

  • Mover S
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover TE
  • Mover TE R
  • Mover TE R4 

 

Mover spacer kit 60 mm

To balance out the height of caravans with a frame height of < 140 to 80 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 60 mm for height adjustment

To balance out the height of caravans with a frame height of < 140 to 80 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 30 mm

To balance out the height of caravans with a frame height of < 170 to 110 mm. Suitable for Mover systems built after 05/12. 

Mover spacer kit 30 mm for height adjustment

To balance out the height of caravans with a frame height of < 170 to 110 mm. Suitable for Mover systems built after 05/12. 

Short mounting system

Alternative mounting if the Mover cannot be attached because of substructures or interfering edges. In Germany, a test certificate (TÜV) is required, apart from Mover XT and Mover SX.

Short mounting system

Alternative mounting if the Mover cannot be attached because of substructures or interfering edges. In Germany, a test certificate (TÜV) is required, apart from Mover XT and Mover SX. 

Also suitable for

  • Mover SE R
  • Mover TE R
  • Mover TE R4 (2 pieces)

 

Eriba Touring adapter kit

Enables installation of a Mover on a chassis with a rectangular profile, such as the single-axle Eriba Touring caravan.
 

Mover Eriba Touring adapter kit

Enables installation of a Mover on a chassis with a rectangular profile, such as the single-axle Eriba Touring caravan.

Suitable for

  • Mover S
  • Mover SX
  • Mover SR
  • Mover SE
  • Mover SE R
  • Mover XT 
  • Mover smart

 

Mover mudflap kit

Is used when the original mudflaps no longer fit after installation of the Mover behind the axle. Including instructions and template to adapt mudflaps. 

Mudflap kit for Mover manoeuvring systems

Is used when the original mudflaps no longer fit after installation of the Mover behind the axle. Including instructions and template to adapt mudflaps. 

  • Message
  • Service Helpline
  • Service Centre
  • Dealer search

One number for all cases:

+49 (0) 89 4617-2020

Do you have a question about a product, would you like to arrange an appointment with a Truma Service technician or do you need assistance? Just call us.

                            
Service times:

Due to the current situation we have restricted or service times.

Monday to Thursday from 8 a.m. to 4:30 p.m.
Friday from 8 a.m. to 1 p.m.
                                                   

If you have a question about an appliance, always have information about the appliance type, year of manufacture and factory number at hand. You'll find this on the type plate on the appliance.

Truma type plate

Our service workshop in Putzbrunn is open again from 25.5.2020

Out of responsibility for the health of our employees and customers, we have restricted operations at Truma due to the current situation until further notice.

                                         

You can still reach our Service Centre by

                                          

calling +49 (0)89 4617-2020  and sending an e-mail to  service@truma.com 

                             

Truma Servicewerkstatt
Michael-Haslbeck-Straße 13
85640 Putzbrunn, Germany

No sale of spare parts / Please do not send any equipment to Truma without being requested to do so.

 
 

Find your nearest Truma Dealer.

We use cookies to ensure optimum design and continuous improvement of our website. By using the website, you agree to the use of cookies. Accept More information