Recommended accessories for Mover® manoeuvring systems.

SolarSet 23 to preserve your battery charge

Carefree through the winter with the help of the sun

• Protects your battery against deep discharge
• Secure roof fastening system, certified by DEKRA
• Perfectly matched components

Charge preservation kit with solar module (monocrystalline, 23 Wp), solar charge controller and solar installation kit.

Mover® PowerSet (Plus)

With OPTIMA® YellowTop® battery
Say goodbye to weak batteries with the perfect accessory for your Mover®.  The Truma Mover® PowerSet consists of top-of-the-range products working in perfect harmony with one another.  Together they ensure that your Mover® provides you with power for up to 50% longer.

Scope of delivery

• 1 OPTIMA® YT S 4.2 (55 aH) or OPTIMA® YT S 5.5 (75 Ah) battery, Plus version
• 1 Automatic Charger BC 416 IU
• 1 temperature sensing device (2m)
• 1 battery cut-off switch
• Cables

These entirely maintenance-free OPTIMA® YellowTop® batteries from global market leader Johnson Controls combine the benefits of a starter battery with those of a supply battery thanks to spiral cell technology.  To ensure these high-quality batteries are always at optimum charge, the Automatic Charger BC 416 IU uses state-of-the-art microprocessor-controlled switching technology which is perfectly regulated by the temperature sensing device supplied.
Cables are not included in the scope of delivery.

Attention!  Accessories (such as fuses and terminal clamps) are not included in the scope of delivery.

Mover® FuseSet

The Mover® FuseSet consists of two fuse holders with appropriate fuses integrated for the measurement cable (2 A) and main charging cable (maxi, 30 A).

• Part no: C11000-07300

Battery cut-off switch

The single-pole battery cut-off switch is connected to the minus terminal of the battery. It interrupts the circuit, thereby reducing the risk of short circuits. Also useful as an additional anti-theft device.

• Part no: 60010-05000

Temperature sensing device

Controls temperature-guided, optimum charging of your precious battery, in conjunction with an appropriate Automatic Charger. Available with two cable lengths (2 m, 6 m), incl. mounting accessories.

• Part no: 2m - C11000-00700, 6m - C11000-00800.

Quickpower terminal clamps

Quick-acting battery terminal clamps for straightforward connection and disconnection of battery connections by hand. Suitable for all DIN and SAE-compliant connections. Can support up to 150 A with continuous load, 800 A with short-term load.

• Part no: C11000-02100

Spacer set 30 mm

For compensating the height difference for caravans / trailers with a frame height of less than 170 mm and up to 140 mm.

Spacer set 60 mm

For compensating the height difference for caravans / trailers with a frame height of less than 140 mm and up to 110 mm.

Low chassis kit

Consisting of mounting plates for compensating for a chassis height of less than 110 mm (includes screws and nuts). Attention: If drilling is required for installation on the chassis, subsequent inspection and approval by an officially recognised expert is required (TÜV; in Germany). If the low chassis kit is used with the AL-KO Vario III/AV chassis, the vehicle frame must not be drilled into under any circumstances!

• Part no: 60010-64900

Low chassis kit, short

For compensating the height difference for caravans / trailers with a frame height of less than 110 mm.

Attention: In Germany, this installation kit must be accepted by a vehicle expert.

Installation kit AL-KO Vario II/AV

Two reinforcing plates incl. screws and instructions.

Essential for reinforcing the frame of single-axle caravans with AL-KO Vario III/AV single chassis and a frame thickness of less than 2.8 mm.

• Part no: 60010-21500

Eriba Touring

Installation kit; add-on for the rectangular profile

• Part no: 60030-09000